【ヘッド交換】古すぎて現行ヘッドではサイズの合わないコンガ!皮ヘッドのコンガスキンワイヤーの交換(2)【修理DIY】
一晩、水につけて柔らかくしました。
今度はどうでしょうか。
コンガに乗せてスキンワイヤーとフープを乗せます。
徹底的に柔らかくしたので折り目がなくなり、コンガスキンワイヤーを包んで折り返してフープで挟むことができません。
挟んでもすぐに元に戻ります。
悪戦苦闘する姿をしばらく見て楽しみましょう。
作戦変更。
対角線状にタコ糸を結んで皮の縁を引っ張ってみます。
さっきよりマシな感じです。
しかしもう一歩のところでうまくできません。
急がば回れ。
タコ糸の数を増やしました。
良さそうな雰囲気ですね?
これで鉄壁です。
この戦いに負ける気がしません。
あと、ラグがどうやってもフープに届かないので、靴紐でフックに結びました。
とりあえずこの状態で皮を引っ張って、伸ばしてからラグをかけようという計画です。
だんだんと締め上げていきます。
皮もフープとの間に挟まって取れることもないだろうと判断。
タコ糸を切っていきます。
愚かな!
あとで失敗に気づきます。
タコ糸、全部切る。
完成が見えてきました。
良い気になってナットを締めていきます。
早回し〜
衝撃!皮がフープとの間からするっと抜けました。まだ皮が柔らかかったのでナットを締めるうちにずるずると動いていたようです。
衝撃すぎて撮影を忘れました。
やり直し人生。
衝撃からまだ立ち直っていません。
もう一度タコ糸を結びました。
どうやら皮が柔らかい間はタコ糸を切ってはいけなかったようです。
再び、ナットを締めていきます。
あと靴紐が切れそうだったのでクレモナロープで補強しました。
作戦変更。
今はヘッドの形だけを作っておいて、皮の折り返し部分がある程度乾いてから、引っ張ることにします。
皮は乾くと硬くなるので折り返し部分が抜けなくなります。
タコ糸が切れない範囲である程度、ナットを締めておきます。
今日はここまで
待て次号。
[Head replacement] A conga that's too old to fit with the current head! Replacing the skin wire on a leather head (continued) [DIY repair]
I soaked it in water overnight to soften it.
How about this time?
I put it on the conga and then put the skin wire and hoop on it.
Because it's been thoroughly softened, there are no creases, so I can't wrap the conga skin wire around it and fold it back to clamp it with the hoop.
Even if I clamp it, it goes back to normal immediately.
Let's enjoy watching him struggle for a while.
Change of strategy.
I tie some string diagonally and try pulling the edge of the skin.
It feels better than before.
But I can't get it right in the next step.
Slow and steady wins the race.
I increased the number of strings.
It looks good, doesn't it?
Now it's ironclad.
I don't feel like I'm going to lose this battle.
Also, the lug wouldn't reach the hoop no matter what I did, so I tied it to the hook with a shoelace.
For now, I plan to pull the leather in this state, stretch it, and then put the lug on.
I gradually tighten it.
I decide that the leather will get stuck between the hoop and the string, and won't come off.
I cut the string.
How stupid!
I realize my mistake later.
I cut all the string.
I can see the end in sight.
Feeling good, I start tightening the nut.
Fast forward ~
Shock! The leather slips out from between the hoop. The leather was still soft, so it seems to have been moving around as I was tightening the nut.
I was so shocked that I forgot to take a picture.
Life starting over.
I still haven't recovered from the shock.
I tied the string again.
It seems I shouldn't have cut the string while the leather was soft.
I tightened the nut again.
Also, my shoelaces were about to break, so I reinforced them with Cremona rope.
Change of plan.
For now, I'll just make the shape of the head, and once the folded part of the skin has dried somewhat, I'll start pulling it.
When the skin dries, it hardens, so the folded part won't come off.
Tighten the nut as much as possible, but not enough to break the string.
That's all for today.
Wait for the next issue.